BIN DUMPER / TOTE DUMPER,
food grade, stainless steel,
floor-level in-feed box tipper
for up to 48 by 48 inch bins,
hydraulic powered;
--IN STOCK NEW.

Alard Model BD48 floor-level-loading food grade stainless steel forward bulk box dumper, for discharging vegetables, fruits, food products, or other bulk materials from heavy bins, crates, totes, and/or Gaylords. Typically used as a raw product infeed dumper for industrial food processing applications. In stock new and available for fast delivery.

FEATURING:

• Sized for standard 48 inch by 48 inch bin, or smaller, with bin holder measuring 54 inches wide by 48 inches long by 42 inches deep.
  
  
• Manually adjustable hold-down bar with adjustment steps for 28.5 inches high, 35.5 inch bin height, and 53.5 inches high bin clearance. Other hold-down settings can be provided on request; --CALL 315-589-4511 with your tote size specifications.
  
  
• Food grade sanitary stainless steel construction.
  
  
• Heavy duty tubular stainless steel frame construction.
  
  
• Dump action provided by (2) 3.5-inch diameter hydraulic cylinders powered by a self-contained 2 HP hydraulic power pack with reservoir and manual controls, set for 208/230/460 volt 3 phase electrical input (unless otherwise specified).
  
  
• Configured for FLOOR LEVEL IN-FEED for convenient hand-truck loading...
  
  
  • ...with a 38 inch pivot point, and a 40 inch dump height from the edge of the dumper in a 45 degree fully inverted position (overall height and dump height from bin depend on the height of the bin). Support stands to raise the height of the dumper for fork-lift loading and a higher dump height are available as an option and will be quoted upon request, based on customer specifications. Call 315-589-4511 to discuss your bulk food product dumper needs.

As of this writing, this NEW forward bin dumper is new, in stock at Alard, and available for immediate shipment.

CALL 315-589-4511 to confirm availability, and to discuss your particular food grade bulk material handling needs.

Alard item reference #: Y5806

STATIC SCREEN SEPARATOR,
Alardsieve 24x36 hydrosieve screen,
all stainless steel...

A new Alardsieve 2436 water recovery screener / scalper hydrasieve screener, for food grade solids separation, wash-water filtration, and/or waste-water recovery. A Hydrasive type static screen sieve for separating solids from water and/or other liquids such as cooking oils.

This stationary screen is configured with a special triangular-rod / wedge-wire screen specifically designed for liquid-solid separation screening, with very precise and consistent sieve opening sizes. Product / solids in a liquid such as water or oil pass over the stationary screen. The liquid passes through the screen to a collection tank and drain, leaving the solids to pass over the screen for collection beneath.

An ideal static sieve screener-separator for wash-water reclaim / reuse, by-product recovery, and / or otherwise removing solids from waste water in industrial food processing plant applications such as peeling, coring, and grading operations for removing stems, seeds, leaves, and other foreign materials from rinse water. Also commonly used in other municipal and plant waste-water treatment facilities for solids removal filtration.

FEATURES:

• 24 inch wide by 36 inch long (top to bottom) static wedge-wire screen.
  
  
• .040 inch sieve-opening-size screen installed; --other standard sieve opening sizes can be sourced and installed to order, from .010 inch to .100 inch, with other sizes to be priced upon request. CALL 315-589-4511 to tell us YOUR sieve size specification.
  
  
• Screens are slide-out / slide-in interchangeable for a wide range of solids separation applications.
  
  
• 33 inch deep full-width infeed / head tank, tapering from 20 inches front-to-back at the top to 15 inches front to back at the bottom. The headbox is open and easily cleaned of debris such as stones or other such "heavies".
  
  
• Complete with dispersion shield over the weir to spread water evenly across entire screen, for optimal laminar flow.
  
  
• 4 inch threaded inlet, 6 inch threaded outlet; --allows for optional flange fittings to be screwed on, or for hose fittings to be cinched on to infeed and discharge connections.
  
  
• 4 inch diameter clean-out ports on either side (for easy access behind screen), with 1 inch tank drains at bottom level for comprehensive rinsing, cleaning and drainage of wash water.
  
  
• 1.25 inch diameter cleanout drain in each tank.
  
  
• Throughput capacity depends on screen sieve opening chosen. For example, with a .040 inch (1mm) sieve opening, a throughput capacity of approximately 400 gallons per minute capacity is feasible running non-greasy solids (actual throughput will depend on solids and flow characteristics).
  
  
• All food grade 304 stainless steel construction.
  
  
• Static screen / stationary screen water recovery sieve has no moving parts, making it a low cost, low maintenance and long-lived dewatering system.
  
  

As of this writing, this food grade solids separation / static dewatering screen is new, in stock at Alard, and available for immediate shipment.

CALL 315-589-4511 to confirm availability, and to discuss your liquid solid separation equipment needs.

Alard item reference #: Y5858

TWO LANE
FLAT-TOP CONVEYOR,
table-top chain conveyor,
L-shaped, 90 degree turn,
all stainless steel...

An ARROWHEAD food grade stainless-steel-body TABLETOP CONVEYOR with dual 7.5 inch wide Delrin chain lanes and 90 degree left- angle turn.

FEATURING:

• Dual 7.5 inch wide plastic table top belts run side by side for a total belt width of 15.5 inches.
  
  
• L-shaped with 90 degree turn:
  
  
  • 96 inch long infeed.
    
    
  • 189 inch long discharge.
    
    
  • 44 inch working height with stainless steel legs & adjustable foot pads.
    
    
  • Rail supports on sides (rails not included).
    
    
  • 2 HP drive motor.
    
    
  • 3 phase electrical input.

As of this writing, this left-angle turn conveyor is in stock at ALARD, in GOOD condition, available for timely shipment.

CALL 315-589-4511 to confirm availability, and to discuss your particular industrial food processing transfer caonveyor equipment needs.

ALARD item reference #: Y3744

FOOD PROCESS METAL DETECTOR
with BELT CONVEYOR, 14x6 opening,
food grade, stainless steel...

A refurbished FORTRESS BSH metal detector, on a new stainless steel thru-conveyor, with belt-stop alarm reject. A food grade belt transfer metal detection system for food processing and/or other industrial process applications.

FEATURING:

• 5 7/8 inch high by 14 inch wide USABLE aperture.
  
  
• Stainless steel detection head with new epoxy liner.
  
  
• Digital operator control panel.
  
  
• NEW stainless steel conveyor frame.
  
  
  • 11.75 inch wide by 87 inch long plastic interlocking chain belt:
    
    
  • Left to Right product flow.
    
    
  • Variable speed control.
    
    
• 34 inch working height with threaded rod adjustable feet.
  
  
• Food grade sanitary stainless steel construction
  
  
• Belt stop alarm reject.
  
  
• 1/2 HP stainless steel shrouded washdown motor.
  
  
• 110 volt single phase (household current) electrical input.
  
  

As of writing this refurbished Fortress metal detector is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your industrial process food safety product inspection needs.

ALARD item reference #: Y5725

Safeline
FOOD PROCESS METAL DETECTOR
with BELT CONVEYOR, 26x8 opening,
food grade, stainless steel...
 

A refurbished SAFELINE metal detector, on a new stainless steel thru-conveyor, with belt-stop alarm reject. A food grade belt transfer metal detection system for food processing and/or other industrial process applications.

FEATURING:

• 8 inch high by 25.5 inch wide USABLE aperture.
  
  
• Stainless steel detection head with two (2) frequencies, providing versatile adjustability for both wet and dry applications.
  
  
• Digital operator control panel.
  
  
• New stainless steel conveyor frame.
  
  
  • 25.5 inch wide by 87 inch long plastic interlocking chain belt.
    
    
  • Left to Right product flow.
    
    
  • Variable speed control.
    
    
• 32 inch working height with threaded rod adjustable feet.
  
  
• Food grade sanitary stainless steel construction.
  
  
• Belt stop alarm reject.
  
  
• 1/2 HP stainless steel shrouded washdown motor.
  
  
• 110 volt single phase (household current) electrical input.
  
  

As of writing this refurbished Safeline metal detector is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your industrial process food safety product inspection needs.

ALARD item reference #: Y5726

FOOD PROCESS METAL DETECTOR
with BELT CONVEYOR, 20x8 opening,
food grade, stainless steel...

A refurbished FORTRESS Phantom metal detector, on a new stainless steel thru-conveyor, with belt-stop alarm reject. A food grade belt transfer metal detection system for food processing and/or other industrial process applications.

FEATURING:

• 8 inch high by 20 inch wide USABLE aperture.
  
  
• Stainless steel detection head with new epoxy liner.
  
  
• Digital operator control panel.
  
  
• NEW stainless steel conveyor frame.
  
  
  • 18 inch wide by 84 inch long plastic interlocking chain belt:
    
    
  • Left to Right product flow.
    
    
  • Variable speed control.
    
    
• 32 inch working height with threaded rod adjustable feet.
  
  
• Food grade sanitary stainless steel construction
  
  
• Belt stop alarm reject.
  
  
• 1/2 HP stainless steel shrouded washdown motor.
  
  
• 110 volt single phase (household current) electrical input.
  
  

As of writing this refurbished Fortress metal detector is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your food safety product inspection needs.

ALARD item reference #: Y5562

VIBRATING FEEDER,
vibratory shaker-feeder,
food grade, all stainless steel...

Key Iso-Flo vibratory conveyor for even-feeding to downstream equipment, such as a radial combination scale, cutting machine, filling machine, peeling machine or whatever food processing or packaging equipment.

FEATURES:

• Vibrating conveyor bed measuring 91.5 inch overall length by 18 inch wide.
  
  
  • Smooth flat stainless steel contact surfaces.
    
    
  • 6 inch high sidewalls.
    
    
  • Half-moon shaped discharge.
    
    
• Mounted on stainless steel legs with isolation springs. Can also be mounted from overhead, e.g. suspended from the ceiling, such as for feeding a radial combination scale. Call 315-589-4511 to discuss your particular bulk food product conveying and feeding requirements.
  
  
• Approximately 30 inch infeed height, 24 inch high discharge.
  
  
• All food grade sanitary stainless steel construction.
  
  
• New style Key Iso-Flo eccentric drive.
  
  
• 1 HP belt drive motor with adjustable pulleys to increase/decrease shake.
  
  
• 208 / 230 / 460 volt 3 phase electrical input.

As of this writing, this vibrating shaker-feeder is in stock at ALARD, in EXCELLENT operational, mechanical, electrical, and cosmetic condition; available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your industrial food process bulk food conveying / feeding needs.

ALARD item reference #: Y5035

52 gallon steam-jacketed pressure TANK, food grade, stainless steel...

A BOWA GmbH 200 LITER (52 gallon) steam jacketed pressure vessel, food grade, stainless steel, vertical TANK, with dome top and dish bottom.

FEATURES:

• 31 inch diameter by 55.5 inch deep jacketed vessel.
  
  
• 25 liter (6.6 gallon) jacket - CE certified.
  
  
• Dome top:
  
  
  • Lugged center cover with rubber seal.
    
    
  • 2.5 inch and 3.5 inch Tri-clamp inlet ports.
    
    
• Dished bottom with 1.5 inch center bottom outlet with manual valve and Tri-clamp connection for 7 inch high discharge.
  
  
• Jacket and internal pressure tagged for 58 psi.
  
  
• Air inlet, pop off valve and psi gauge.
  
  
• All food grade sanitary stainless steel construction.

As of this writing, this jacketed pressure tank is in-stock at ALARD, in VERY GOOD condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your food processing needs.

ALARD item reference #: Y3786

SIX ROLL continuous
PEELER-WASHER-SCRUBBER
for fruits and vegetables,
hydraulic powered, stainless steel,
for abrasive peeling
or as a brush washer...

A Magnuson Model WSP-2066 hydraulic driven 6-roll continuous abrasive peeler, brush washer, scrubber for fruits and vegetables, especially root crops such as potatoes, carrots, beets, cassava, radishes and other similar products in the context of industrial food processing and pre-cut packing line operations.
 

FEATURES:

• Currently configured with three (3) brush rolls and three (3) abrasive rolls - can be set with any combination of abrasive and/or brush rolls, with a range of grit and/or brush options for more or less peeling action.
  
  
• Peeling / Scrubbing rolls are powered by a 10 HP self-contained hydraulic power pack.
  
  
• 18 inch by 12 inch top hopper inlet opening on the hinged stainless steel cover at a 73 inch infeed height.
  
  
• Lubricating and rinsing action are provided in the chamber via a water spray header with spray nozzles.
  
  
• Retention time is controlled by a manually adjustable discharge gate at 48 inches high.
  
  
• Water, peels and debris drop to a full-length sloped water catch pan with a 6 inch center bottom outlet.
  
  
• Locking 7.5 inch locking casters for added mobility.
  
  
• All food grade sanitary stainless steel body.
  
  
• 460 volt 3 phase electrical input.

As of this writing, this six roll peeler is in stock at ALARD, available for timely service and shipment.

CALL 315-589-4511 to confirm availability and discuss your particular fruit and / or vegetable peeling and washing equipment needs.

ALARD item reference #: Y4528

CENTRIFUGAL PUMP,
2 inch inlet, 1.5 inch outlet,
with 1 HP MOTOR,
food grade, stainless steel...

An SPX/APV Model 4V2 stainless steel body centrifugal pump designed for small flow capacity with minimum head pressure for a multitude of fluid handling applications ranging from food products, washing, rinsing, recirculation, irrigation, general industrial & municipal use.

FEATURING:

• Manufacturer rated for 85 gallons per minute at 33 feet of head - pump curves available upon request.
  
  
• 5 7/8 inch diameter 4-blade impeller.
  
  
• 2 inch diameter inlet / 1.5 inch diameter outlet with Tri-clamp fittings.
  
  
• Food grade sanitary stainless steel pump.
  
  
• 1 HP 1740 rpm direct drive motor.
  
  
• 208/230/460 volt 3 phase electrical input.
  
  

As of this writing, this centrifugal pump is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your particular industrial food process pump and bulk material handling needs.

ALARD item reference #: Y5847

VOLUMETRIC AUGER FEEDER
with HOPPER,
1.75 inch diameter feed tube,
bulk solids metering feeder,
food grade, stainless steel...

A Schenck AccuRate "Tuf-Flex" mass flow hopper, dry ingredient feeder, is designed to handle virtually any dry material, including fine powders, granules, flakes, fibers, dry coatings, spices, seasonings, chips & pellets, without packing or bridging. The product feed hopper features a flexible vinyl chamber which is externally massaged for continuous even flow of uniform material. AccuRate Volumetric Series Feeders are manufacturer rated for industrial process applications including food, pharmaceutical, chemical, plastics and more.

FEATURING:

• Manufacturer rated for +/- 0.5% to 3.0% accuracy - depending on materials & flow rate.
  
  
• 17 inch square by 21 inch deep tapered stainless steel hopper.
  
  
  • Flexible vinyl feed chamber with external thumpers.
    
    
  • Solid stainless steel cover with 5.75 inch diameter infeed.
    
    
  • Safety pour grid.
    
    
  • 1.75 inch diameter by 25 inch long auger screw.
    
    
• 39 inch high infeed, 4 inch discharge height.
  
  
• Two (2) 3/4 HP washdown motors.
  
  
• 208/230/460 volt 3 phase electrical input.
  
  

As of this writing, this volumetric feeder is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition and available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your industrial food processing equipment needs.

ALARD item reference #: Y5860

Tri-Clover PR25
Food Grade ROTARY LOBE PUMP
1.5 inch inlet and outlet,
with motor and base...

A Tri-Clover PR25 sanitary positive displacement rotary lobe pump with motor and base, for pumping viscous fluids, slurry and / or particulate bearing liquids in industrial food, canning, bakery & beverage processing applications.

FEATURING:

• 1.5 inch inlet and discharge ports with threaded connections in a horizontal flow orientation.
  
  
• Manufacturer rated for...
  
  
  • ...up to 28 gallons per minute,
    
    
  • 20 psi working pressure,
    
    
  • and up to 140 degrees Fahrenheit product temperature.
    
    
• Food grade sanitary stainless steel pump, with stainless steel lobes...
  
  
• ...coupled to a NEW 3HP SEW Eurodrive motor.
  
  
• Stainless steel base.
  
  
• 208 / 230 / 460 volt 3 phase electrical input.

As of this writing, this lobe pump is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition - available for immediate shipment.

CALL 315-589-4511 to confirm availability, and to discuss your particular industrial food process pump and bulk material handling needs.

ALARD item reference #: Y5833

BAG PACKING TABLE,
2-station, food grade, stainless steel,
for filling bags by weight,
with scales & bag holders...

Keep productivity and profits in clear sight with the Alard Model BT2020, 2-spout food grade stainless steel bag filler table with weigh scales and bag holders for bag-filling of precut produce by weight, such as freshcut vegetables, leafy salad mixes, florets and fresh peeled whole products. Note: single station version also available; --call 315-589-4511 to discuss your fresh produce packing needs.

FEATURES:

• This stainless steel two-person BAGGING TABLE measures 43 inches long by 75 inches wide with sides that taper from 13.75 inches high at the back down to 5.75 inches in the front.
  
  
• This bag filling manual pack table features an ANGLED BACK in order to feed product closer to the operator's reach. The flat-bottom portion of the table is only 29.5 inches in depth (from front to back), while the angled back-stop allows for additional full-load capacity.
  
  
• Two (2) 30 lb electric washdown scales with over-under remote readout display head mounted at eye level; one for each hand-packing station.
  
  
• Each bag-filling station has a standard 6.5 inch diameter filling tube, which can be fitted with an optional stainless steel filling funnel for larger or smaller bag sizes.
  
  
• Each filling tube is equipped with a stainless steel pneumatic bag holder to keep the bag held in position during the bag-filling process.
  
  
• Beneath each bag holder is a 10 inch deep (front to back) by 12 inch wide (side to side) stainless steel weigh cell platform which is height adjustable to accommodate different bag lengths.
  
  
• All food grade sanitary stainless steel construction.
  
  
• 110 volt single phase (household current) electrical input.
  
  
• Compressed air required for the pneumatic bag holders.
  
  
• NEW.
  
  

OPERATION:

• Each operator hangs a bag on their filling funnel and engages the bag holder by pressing a button.
  
  
• The operator then pulls product from the table into the filling tube until the proper weight is made.
  
  
• Overages can easily be removed.
  
  
• The operator then disengages the bag holder and removes the bag, puts a new bag in place & the bag packing process is repeated.
  
  

This particular item was the prototype machine for this model bag filler, and as of this writing, is in stock new at Alard, fully assembled and ready-to-go, available for immediate shipment.

CALL 315-589-4511 to confirm current availability and discuss your food handling needs.

ALARD item reference #: Y5694

FOOD PROCESS METAL DETECTOR
with BELT CONVEYOR, 14x6,
food grade, stainless steel...
 

A refurbished FORTRESS BSH metal detector, on a new stainless steel thru-conveyor, with belt-stop alarm reject. A food grade belt transfer metal detection system for food processing and/or other industrial process applications.

FEATURING:

• 5 7/8 inch high by 14 inch wide USABLE aperture.
  
  
• Stainless steel detection head with new epoxy liner.
  
  
• Digital operator control panel.
  
  
• NEW stainless steel conveyor frame.
  
  
  • 11.75 inch wide by 87 inch long plastic interlocking chain belt:
    
    
  • Left to Right product flow.
    
    
  • Variable speed control.
    
    
• 34 inch working height with threaded rod adjustable feet.
  
  
• Food grade sanitary stainless steel construction
  
  
• Belt stop alarm reject, with new, integrated, gasketed PVC conveyor control box.
  
  
• 1/2 HP stainless steel shrouded washdown motor.
  
  
• 110 volt single phase (household current) electrical input.
  
  

As of writing this refurbished Fortress metal detector is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your industrial process metal detector needs.

ALARD item reference #: Y5724

LENGTH SLICER, ROMAINE TRIMMER, butt cutter, segment cutting machine, all stainless steel...

The F.I.R.M. Inc. Model A.R.T.T.S. is an efficient high-capacity industrial length cutter, tip & butt trimming machine, vegetable topper-tailer, length slicer, segment cutter, and/or increment cutter, for pre-cut produce / fresh-cut processing and preparation operations for food products such as romaine lettuce, celery, carrots, zucchini and other oblong shaped produce.

FEATURING:

• Sloped 18 inch long stainless steel in-feed section.
  
  
• 20 inch wide by 14 foot long cleated infeed belt with two lanes of 3.5 inch wide by 2 inch high cleats on 3 inch centers.
  
  
• 20 inch wide by 36 inch long hold down belt with adjustable counterweight.
  
  
• Eight (8) 12 inch diameter serrated blades - currently set for 1.5 inch long segments with top & butt.
  
  
• 20 inch wide by 12 foot long waste takeaway belt.
  
  
• Open frame design for ease of sanitation.
  
  
• 18 inch wide by 11 foot long operator catwalk with 33 inch working height.
  
  
• All food grade sanitary stainless steel construction.
  
  
• 1 HP stainless steel shrouded drive motor.
  
  
• 208 / 230 / 460 volt 3 phase input.
  
  
• Previously used for making Caesar salad cuts of romaine lettuce, whereby the carrying belt was in-plant modified for that purpose. We did not elect to replace the (good usable) belt on this machine in advance of sale, since choice of flights, flight spacings, and / or other configuration aspects for this machine, would be dependent on the buyer's application requirements. Call 315-589-4511 to discuss your increment cutting, segment cutting, romaine lettuce cutting needs.
  
  
• ! NOTE ! --To be equipped with gasketed PVC operator control box with safety interlock system prior to shipment, or buyer to agree in writing to install same if purchased "as-is" for immediate shipment.

As of this writing, this length cutter is in stock at ALARD, in VERY GOOD condition, available for timely shipment.

CALL 315-589-4511 to confirm availability and discuss your particular industrial process vegetable preparation / cutting equipment needs.

ALARD item reference #: Y5288

BROWN 202 PADDLE FINISHER separator, pulper, all stainless steel...
 

This Brown International Model 202 PADDLE FINISHER, pulper, refiner, separator is manufacturer recommended for extracting juices and purees from fruits & vegetables, and separate fruit flesh (pulp) from fruit pits, seeds and/or other solids (stems, skins).

OPERATION:

• This make / model pulping / finishing machine uses spinning paddles turning inside a perforated screen. The screens are interchangeable, and the perforation size of the screen determines the "finish" of (amount of pulp in) the product.
  
  
• Liquids (juices and pulp) that pass through the screen are collected in a bottom discharge pan while the solids (pits, seeds, skins) remaining inside the screen are discharged out the end.
  
  
• Manufacturer recommended for industrial capacity food processing of apricots, pumpkin & squash, pears, apples, plums, prunes, figs, citrus juices, jam, soup, peanut butter, jelly and fruit nectar.

FEATURES:

• Manufacturer rated for input rates of up to 120 gallons per minute.
  
  
• 4 inch diameter PIPE -or- 6 inch by 12 inch hopper infeed.
  
  
• Set with .033 inch perforated screens -- other sizes available. CALL 315-589-4511 to discuss your pulper-finisher-separator needs.
  
  
• Solid paddles are individually adjustable for distance to screen.
  
  
• Stainless steel hinged side covers.
  
  
• Bottom collection pan with triclamp outlet.
  
  
• All food grade sanitary stainless steel construction.
  
  
• 20 HP belt drive motor.
  
  
• 575 volt 3 phase electrical input for Canadian voltage, transformer available for domestic US voltage.
  
  

As of this writing, this paddle finisher is in stock at ALARD, in excellent operational, mechannical, electrical, and cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your particular pulping /finishing equipment needs.

ALARD item reference #: Y5811

MARCHANT SCHMIDT
CHEESE BLOCK CUTTER,
food grade sanitary, stainless steel...

DEMO VIDEO
CHEESE BLOCK CUTTER, pre-cutter, Y3746
from Alard Equipment Corporation.

This Marchant Schmidt pneumatic cheese portion wire cutter is a two-stage cheese cutting machine; a two-dimensional cheese block pre-cutter designed to produce a variety of cut sizes and shapes: cubes, sticks, bars, bricks and chunks for further processing applications. Cheese is pushed vertically, then horizontally, through both cutting grids, so as to cut two dimensions with one block placement.

FEATURES:

• Designed for standard 40 pound 20 kilogram cheese loaves:
  
  
  • Recommended 34F - 45F (1C - 7C) product temperature for optimal cutting.
    
    
  • 11.5 inch by 14.5 inch by 7.5 inch high maximum product input.
    
    
• Came with two sets of harp wire cutting grids set for 1.5 inch cubes, either of which could be easily reset to cut other shapes / sizes. Call 315-589-4511 to discuss your cheese cutting specifications.
  
  
• Manufacturer rated for up to 50 cycles / 2,000 lbs per hour. In our testing, cycle time was faster, about 40 seconds (but running without product). 
  
  
• 36 inch high infeed, 22 inch discharge height.
  
  
• Two-hand activation operator control with interlock system for operator safety.
  
  
• All food grade sanitary stainless steel construction.
  
  
• 110 volt single phase electrical input.
  
  
• 90 psi @ 12 cfm compressed air input.
  
  
• Previously used in a two-step cutting process, to pre-cut cheese prior to feeding into a shredder.

As of this writing, this cheese cuber is in stock at ALARD, LIKE NEW and in excellent operational, mechanical, electrical, pneumatic & cosmetic condition; available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your particular food process cutting equipment needs.

ALARD item reference #: Y3746

BIN DUMPER / TOTE DUMPER for 40 by 48 inch bins, food grade, stainless steel, hydraulic powered; --IN STOCK NEW...

Alard Model BD40 food grade stainless steel forward bulk box dumper, for discharging vegetables, fruits, food products, or other bulk materials from heavy bins, crates, totes, and/or Gaylords. Typically used as a raw product infeed dumper for industrial food processing applications. In stock new and available for fast delivery.

FEATURES:

• Sized for standard 40 inch by 48 inch bin, or smaller, with bin holder measuring 45.75 inches wide by 48 inches long by 42 inches deep.
  
  
• Manually adjustable hold-down bar with adjustment steps for 28.5 inches high, 35.5 inch bin height, and 53.5 inches high bin clearance. Other hold-down settings can be provided on request; --CALL 315-589-4511 with your tote size specifications.
  
  
• Food grade stainless steel dumper construction, including heavy duty tubular stainless frame.
  
  
• Dump action provided by 3.5 inch diameter hydraulic cylinders powered by a self-contained 2 HP hydraulic power pack with reservoir and manual controls, set for 208/230/460 volt 3 phase electrical input (unless otherwise specified).
  
  
• Comes set for FLOOR LEVEL INFEED with a 38 inch pivot point and a 40 inch dump height from the edge of the dumper in a 45 degree fully inverted position (over all height and dump height from bin depend on the height of the bin). Support stands to raise the height of the dumper are available as an option and will be quoted upon request, based on customer specifications.
  
  

As of this writing, this food grade, stainless steel, floor-level infeed BIN DUMPER is new and in stock at Alard, and available for immediate shipment.

CALL 315-589-4511 to confirm availability, and to discuss your particular food process bulk material handling needs.

Alard item reference #: Y5803

CENTRIFUGAL PUMP,
2 inch in, 1.5 inch out,
with 1 HP MOTOR,
food grade, sanitary, stainless steel...

An SPX/APV Model 6V2 food grade sanitary stainless steel centrifugal pump designed for a multitude of fluid handling applications ranging from food products, washing, rinsing, recirculation, irrigation, general industrial and municipal use.

FEATURING:

• 5 7/8 inch diameter 4-blade impeller.
  
  
• 2 inch diameter inlet / 1.5 inch diameter outlet with sanitary Tri-clamp fittings.
  
  
• Manufacturer rated for 85 gallons per minute at 33 feet of head with 1 HP 1740 rpm direct drive motor.
  
  
• Food grade sanitary stainless steel.
  
  
• 208 / 230 / 460 volt 3 phase electrical input.

As of this writing, this centrifugal pump is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your particular industrial food process pump and bulk material handling needs.

ALARD item reference #: Y5846

100 GALLON VERTICAL TANK,
INSULATED, food grade,
stainless steel...

A BAUER WELDING food grade 100 gallon round, single wall insulated stainless steel tank with dome top and shallow dish bottom.

FEATURING:

• 32 inch diameter by 32 inch high sides.
  
  
• Dome top with 17 inch diameter manway with locking lid.
  
  
• Shallow dish bottom.
  
  
• Two (2) inlets & one (1) vent on top.
  
  
• Side bottom pressure & temperature transmitters.
  
  
• 3 inch side bottom with elbow to side-bottom outlet with Tri-clamp fitting at 7 inch discharge height.
  
  
• Food grade sanitary stainless steel construction including legs.

As of this writing, this Bauer 100 gallon tank is in stock at ALARD, in LIKE NEW condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your food processing needs.

ALARD item reference #: Y5828

ROTARY DRUM BLANCHER,
47 inch diameter by 11 foot 8 inch long,
stainless steel...

DEMO VIDEO
Hughes / Lyco HOT WATER ROTARY BLANCHER, 12x4,
Alard item Y5825 from Alard Equipment Corporation.

A Hughes / Lyco hot water rotary blancher for pasta, rice, dry beans, green beans, carrots, corn, mushrooms, beets, potatoes, sous vide, and many other vegetable & fruit products with through-put rates dependent on product density and hold times. Hot water rotary blanchers are manufacturer rated for uniform heating and controlled transfer, and gentle agitation, with easy to clean sanitary construction, and high capacity in a small footprint.

FEATURES:

• New 47 inch diameter by 11 foot 8 inch foot long blancher reel.
  
  
  • 14 inch flights on 10 inch centers.
    
    
  • Full sparge at each end.
    
    
  • 2 HP stainless steel washdown drive motor.
    
    
• 1/16 inch drum screen perforations.
  
  
• Paddle discharge with perforated chute & catch pan water return.
  
  
• SPX Model 6V2 Centrifugal Pump:
  
  
  • 2.5 inch inlet / 1.5 inch outlet.
    
    
  • 10 HP stainless steel shrouded washdown motor.
    
    
• 8 inch diameter clean-out at both ends.
  
  
• Food grade USDA sanitary stainless steel construction with removable screen panels for cleaning and sanitation.
  
  
• Four (4) point power hood lift driven by 1 HP stainless steel shrouded washdown motor.
  
  
• 460 volt 3 phase electrical input.

As of this writing, this hot water rotary blancher is in stock at ALARD, in very GOOD operable condition available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your particular blanching needs.

ALARD item reference #: Y5825

DEMO VIDEO
SOLBERN Model PTF-DP
TUMBLE FILLER. 

VIDEO DEMO
Solbern PTF-DP TUMBLE FILLER, direct filler, Y4645
from Alard Equipment Corporation.

The Solbern Model PTF-DPG "direct filler" is the "Delicate Product" version of the versatile PTF particulate filler, manufacturer rated for gentle handling and gradual filling to pack whole, sliced, diced and chunky products into cans or jars; filling them completely or partially; even if they are not free flowing.

The Solbern Tumble Filler is configured to shake while progressively filling, so as to orient the product within the container to achieve uniform fill density.

Manufacturer brochure recoomends for products including asparagus (cut), beans (cut), beets (whole, cut, sliced and diced), carrots (cut, sliced, diced or whole baby carrots), corn (whole kernel), dried and soaked beans, lima beans, mixed vegetables, peas, spices, mushrooms (while and/or sliced), potatoes (whole small, cut, sliced and diced), squash (cut, sliced, and diced), sweet potatoes (cut, sliced and diced), tomatoes (peeled, stewed and diced), yams, apples (wedged, cut, diced), apricots (whole, halved, cut, diced), berries, cherries, figs, raisins, dates, grapes, orange and grapefrut sections, peaches (halves and slices), pears (halves), olives, plums, pet-food chunks and particulate, snack foods, dehydrated products, meats, nuts, and shrimp.

FEATURES:

• 10 foot six inch long through conveyor with factory conveyor chain.
  
  
• Manufacturer rated for speeds from 20 to 500 containers per minute, depending on product and container size.
  
  
• Manufacturer rated for a wide variety of vegetables, fruits, dry products and specialty items to an accuracy of 1/10 ounce.
  
  
• Continuous straight-line filling with no indexing or positioning mechanisms required.
  
  
• Manufacturer rated for can sizes from 4 ounce to #10 cans, and glass (or plastic) containers from 2 ounce to half gallon fills. Rapid container size changeover without replacement parts.
  
  
• No product waste, all filling is done within the drum.
  
  
• Food grade stainless steel construction.
  
  
• Complete with operator controls, including variable speed drives on the filling drum, conveyor and track oscillating system.
  
  
• Air required, 80psi, 11cfm.
  
  
• 3 phase electrical input.

As of this writing, this Solbern PTF-DP direct filler is in stock at ALARD, in excellent operational, mechanical, electrical, and cosmetic condition, available for timely shipment.

CALL 315-589-4511 to confirm availability, and to discuss your particular fruit and vegetable processing and packaging needs.

Alard item reference  #:Y4645

FOOD PROCESS METAL DETECTOR
with BELT CONVEYOR, 16x11 opening,
food grade, stainless steel...

A refurbished LOCK METALCHEK Model Met 30+ metal detector, on a stainless steel thru-conveyor, with belt-stop alarm reject. A food grade belt transfer metal detection system for food processing and/or other industrial process applications.

 FEATURES:

• 10.75 inch high by 15.75 inch wide USABLE aperture.
  
  
• Stainless steel search head enclosure.
  
  
• NEMA4 / IP65 digital operator control panel with 100 product presets.
  
  
• Three-frequency levels allowing for optimal sensitivity across a wide range of food products / product  types (wet, dry, salty, meat, fruits, vegetables, fresh, frozen, hot, cold, etc) allowing for maximum versatility with a much wider range of products than a single frequency machine.
  
  
• Sensitivity varies depending on product run, and frequency setting (determined by product characteristics), especially where wet, salty, or acidic products that are electrically conductive introduce "product effect" into the equation; --however this LARGE-opening metal detector has been tested at Alard for a sensitivity of 2mm ferrous, 2mm non ferrous, and 2.5 mm stainless steel at 300 kHz.
  
  
• Stainless steel conveyor frame, with:
  
  
  • 14 inch wide by 60 inch long plastic interlocking chain belt:
    
    
  • Right to Left product flow.
    
    
  • 68 feet per minute.
    
    
• 36 inch working height with threaded rod adjustable feet.
  
  
• Food grade sanitary stainless steel construction
  
  
• Belt stop alarm reject.
  
  
• 1/3 HP conveyor belt drive motor.
  
  
• 110 volt single phase (household current) electrical input.

As of writing this the food grade metal detection system is in stock in excellent operational, mechanical, electrical & cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your industrial process metal detector needs.

ALARD item reference #: Y5352

Lightnin MIXER Model XD30,
portable, clamp-on
food grade agitator...

This SPXFlow Lightnin Classic Series small portable mixer Model XD30 clamp mount agitator is a time-proven classic design for mixing water, oils, brine and agitating other low viscosity (<500 cps) liquid applications.

FEATURING:

• Manufacturer rated for 50 gallons (min) to 500 gallons (max) - dependent on viscosity, temperature, mix time & tank shape.
  
  
• Lightweight, easy to handle.
  
  
• Clamp mount with ball and socket adjusts 90 degrees vertically, 360 degrees horizontally.
  
  
• Three (3) blade prop mixer.
  
  
• 1/2 inch diameter by 32 inch long stainless steel shaft.
  
  
• 1/3 HP 1725 RPM Dura-Mix energy efficient direct drive motor.
  
  
• 208 / 230 / 460 volt 3 phase electrical input.

As of this writing, this clamp-on tank agitator is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition and available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your food processing needs.

ALARD item reference #: Y5857

URSCHEL Model J DICER,
STRIP CUTTER, GREENS CHOPPER.

A two dimensional cutting machine for industrial food processing applications, manufacturer recommended for food products up to 1/2 inch (13mm) thick at infeed, such as spinach and greens, peppers, citrus peel, celery, broccoli, and parsley.

SPECIFICATIONS: Manufacturer literature specifies this model for cutting square or rectangular dices, with...

• Circular knives that can be spaced for cuts from 3/16 inch (4.763mm) to 3 inches (76mm), and...
  
  
• ...a selection of crosscut spindles are available from the manufacturer for cuts from 1/4 inch (6.35mm) to 3 inches (76mm).
  
  
• Strip cuts can be made by removing the crosscut knife spindle from the machine, with the length and thickness of the strips depending on the size of the original product.
  
  

This machine FEATURES:

• Aftermarket safety interlock system with Allen Bradley control box, which disconnects power to the machine if safety guards are removed.
  
  
• 9 inch (229mm) wide feed belt and cutting spindles.
  
  
• Food grade stainless steel product contact surfaces, stainless steel tubular support frame, guards, shrouds & discharge chute.
  
  
• 5 HP brake motor drive.
  
  
• 208 / 230 volt 3 phase electrical input.

As of this writing, this reconditioned Urschel J dicer / strip cutter / greens chopper is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition, needing only to be completed with cutting parts to buyer specification.

CALL 315-589-4511 to confirm availability and discuss your particular industrial food processing needs.

ALARD item reference #: Y5793

STEAM-JACKETED PROCESS TANK with SWEEP AGITATOR, 150 gallon, stainless steel...

The ANCO EQUIPMENT Model BP-WT 150 wing-top BATCH PASTEURIZER TANK, process tank, is designed to heat & cool a variety of dairy, beverage and other liquid food applications. In the context of dairy industry use, this tank is manufacturer rated to both pasteurize and make cheese in one vat. As a 150 gallon jacketed, agitated process tank, it is applicable for a wide variety of food processing applications.

FEATURING:

• 43 inch by 30 inch sloped bottom vessel.
  
  
• Integral stainless steel bridge with multiple triclamp inlets and removable half-moon shaped lids.
  
  
• Bottom anchor sweep agitator with gear reduced for 51 RPM.
  
  
• 45 inch infeed height.
  
  
• 2 inch Tri-clamp front bottom outlet with 14 inch high discharge.
  
  
• Manufacturer rated for pasteurizing 1,290 pounds of milk per batch, but this jacketed process tank with sweep agitation is applicable to a wide range of industrial food processing applications.
  
  
• The insulated, two-zone dimple-plate jacket is manufacturer rated for steam, glycol, or hot water, at 15 psi, and as also having been manufacturer tested for 70 psi / 30 gpm with glycol.
  
  
• All food grade sanitary stainless steel construction.
  
  
• 3/4 HP washdown stainless steel shrouded motor.
  
  
• 208/230/460 volt 3 phase electrical input.
  
  

As of this writing, this Anco jacketed process tank with sweep agitation is in stock at ALARD, in LIKE NEW condition, available for timely shipment.

CALL 315-589-4511 to confirm availability and discuss your food process equipment and process tank needs.

ALARD item reference #: Y5807

JAYHAWK MUSTARD MILL,
food grade, 7.5 HP...

The JAYHAWK Industrial Stone Mill Model 2MPY is a stone grinding mill, a type of colloid mill, for emulsifying, homogenization, dispersing & disintegrating of a variety of food applications including mustards, spices, hot sauces, condiments and more.

FEATURES:

• 7.75 inch diameter proprietary diamond cut stones:
  
  
  • Shown without stones in pictures (see below). Stones are available in 46 or 60 grit per buyer specification.
    
    
• Adjustment handle for stone gap to achieve desired grind size.
  
  
• 1.5 inch diameter infeed.
  
  
• 1 inch by 4 inch wide discharge.
  
  
• 316 stainless steel grinding head, with holder frame included (to hold the head while swung open for cleaning).
  
  
• 7.5 HP direct drive motor.
  
  
• 208 / 230 / 460 volt 3 phase electrical input.

As of this writing, this Jayhawk mustard mill is in stock at ALARD, in GOOD OPERATING condition and available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your food processing needs.

ALARD item reference #: Y5237

VACUUM FILLER / STUFFER...

A VEMAG Robot 500 Type 128/230 vacuum sausage stuffer. A vacuum filling machine for ground meats, portioned doughs, pastes, spreads, soft cheeses, pet foods and other industrial food applications into trays, cups, cans, bottles, jars or tubs.

FEATURES:

• 37 inch diameter by 32 inch deep hinged cone infeed hopper.
  
  
• 67 inch infeed height with adjustable threaded rod feet.
  
  
• Double screw pump with mild steel feed worms.
  
  
• 3 inch diameter discharge with sani-thread fitting - hinged for ease of cleaning.
  
  
• Leg switch activated filling action.
  
  
• Onboard vacuum system.
  
  
• PORTIAMAT analog portioning controls.
  
  
• 208/230 volt 3 phase electrical input.

As of this writing, this Reiser Vemag vacuum filler is in stock at ALARD, in excellent operational, mechanical, electrical and cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your food processing needs.

ALARD item reference #: Y5383

ONION TRIMMER,
TIP and BUTT CUTTER,
CONTINUOUS high volume
topper-tailer...

An Olney Model 4 onion trimmer is a continuous semi-automatic onion trimmer for topping and tailing; a tip and butt cutter for trimming the ends off of onions.

OPERATION:

An operator manually places the product in feed fingers which are mounted on an endless chain. These pass through two circular knives that adjust themselves automatically to the different size product, permitting the same amount to be cut off each onion, regardless of size with a minimum of waste. Product may be placed in the feed fingers without regard to which side either the stem or root are facing, as long as they are oriented from side-to-side.

FEATURES:

• Manufacturer rated for 50 to 70 onions per minute.
  
  
• 4 inch diameter clamps suitable for 3 inch to 4.5 inch diameter onions.
  
  
• Cutting blades automatically adjust to size of the product being cut within its size range - reduces waste but assures close trimming of stem & root.
  
  
• 27 inch wide by 55 inch long by 9 inch deep product infeed hopper.
  
  
• 35 inch long loading section.
  
  
• 41 inch infeed height, 25 inch cut onion discharge height.
  
  
• Food grade sanitary stainless steel construction, including frame & shrouding, with bronze onion clamps.
  
  
• Stainless steel control box with start/stop controls and safety interlock system.
  
  
• Two (2) 1/2 HP belt drive washdown motors.
  
  
• 460 volt 3 phase electrical input.

As of this writing, this continuous onion trimmer is in stock at ALARD, in excellent operational, mechanical, electrical, and cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your particular onion trimming machine needs.

ALARD item reference #: Y5180

VIDEO DEMO
Rietz EXTRUCTOR Model RE-24, MEAT GRINDER, 75 HP...

DEMO VIDEO
RIETZ EXTRUCTOR Model RE-24,
frozen block grinder, 75 HP, Y5863
from Alard Equipment Corporation.

A Rietz Bepex RE-24-K9E943 EXTRUCTOR industrial pulverizer machine, engineered with slow speed and high torque for fracturing, crushing, grinding and tearing large frozen blocks or barrels of bulk materials, such as animal products, meats, cheese, fruits and/or vegetables.

 FEATURING:

• 63 inch long by 29 inch wide by 41 inch deep grinding chamber.
  
  
• 24 inch diameter rotor.
  
  
• 10-spoke discharge plate / die plate / extrusion plate.
  
  
• Bolted on discharge cover with spout, suitable for fitting over, discharging into a 55 gallon drum.
  
  
• 1.25 inch peforations in grind disk.
  
  
• Heavy duty tubular stainless steel frame. 
  
  
• Food grade sanitary stainless steel product contact surfaces with heavy stainless steel support frame.
  
  
• 75 horsepower chain drive motor.
  
  
• 460 volt 3 phase electrical input.
  
  
• Came with bolt-on infeed cover for side-infeed conveyor (feed y5863conveyor not included). 
  
  

As of this writing, this Rietz Bepex EXTRUCTOR is in stock at Alard in EXCELLENT operational, mechanical, electrical and cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your industrial food process cutting, grinding, pulverizing & particle reduction size needs.

ALARD item reference #: Y5863